PET Flake/scrap dehumidifier crystallizer

Reprocessing the flakes in the extruder reduces IV due to hydrolysis i the presence of water, and that’s why pre-drying to a homogeneous drying level with our IRD System can limit this reduction. In addtion, the resin does not yellow because drying time is reduced ( Drying time only needs 15-20mins, final moisture can be ≤ 50ppm, energy consumption less than 60W/KG/H), and shearing in the extruder is thereby also reduced because the preheated material enters the extruder at constant temperature”
send email to us

Products Details

Raw Material PET Recycled flake/ PET sheet scrap/PET Preform scrap   image1
Using Machine LDHW-600*1000 image2
Drying& Crystallized Temperature set 180-200℃Can be adjustable by property of rawmaterial
Crystallized time set 20mins
Final material   Crystallized and Dried PET scraps and final moisture can be about 30ppm image3
>>At first step, the only target is to heat up the material to a preset temperature. Adopt relatively slow speed of drum rotating, the Infrared lamps power of the dryer will be at a higher level, then the PET pellets will have a fast heating till the temperature rises to the preset temperature. >>Drying &Crystallizing step Once the material gets to the temperature, the speed of the drum will be increased to a much higher rotating speed to avoid the clumping of the material. At the same time, the infrared lamps power will be increased again to finish the drying. Then the drum rotating speed will be slowed down again. Normally the drying process will be finished after 15-20mins. (The exact time depends on the property of material) >>After finishing the drying processing, the IR Drum will automatically discharge the material and refill the drum for the next cycle. The automatic refilling as well as all relevant parameters for the different temperature ramps is fully integrated in the state-of-the-art Touch Screen control. Once parameters and temperature profiles are found for a specific material, theses settings can be saved as recipes in the control system.>> Supply Experienced engineer to your factory to help installation and material test running >> Adopt aviation plug, no need to connect the electrical wire while the customer get the machine in his factory. To simplify the installation step >> Supply the operation video for installation and running guide >>Support on line service Normally the PET Bottle flakes or sheet scrap with initial moisture level of up to 10000-13000ppm. The PET Bottle flakes or sheet scrap (Virgin or mixed ) will be recrystallized in Infrared crystal dryer in 20mins, the drying temperature will be 150-180℃ and dried to 50-70ppm,then fed to Single screw extruding system for further processing

● Limiting the hydrolytic degradation of the viscosity. ● Prevent increasing AA levels for materials with food contact ● Increasing the capacity of the production line up to 50% ● Improvement and make the product quality stable-- Equal and repeatable input moisture content of the material

Experienced engineer will make the test. Your employees are cordially invited to participate in our joint trails. Thus you have both the possibility to contribute actively and the opportunity to actually see our products in operation.● Instant start-up and quicker shut down ● Uniform crystallization ● No pellets clumping & stick ● Carefully material treatment ● Up to 60% less energy consumption than conventional drying system ● No segregation of products with different bulk densities ● Independent temperature and drying time set ● Easy clean and change material

Item

IRD Dryer

Conventional Dryer

Transfer medium

None

Hot air

Heat transfer

 Both inside & outside particles together. From outside to inside particle gradually.

Energy

 Save at least 20~50% energy compared to traditional dryer. Consume much energy.

Process time

 1. Crystallization & drying: They are processed simultaneously within about 8~15 minutes. 2. Drying and crystallization at a time 1. Crystallization: About 30~60 minutes. 2. Drying: About 4~6 hours.

Moisturecontent

 1. Under 50-70 PPM after IRD processed. 1. Spend 30~60 minutes to change amorphous PET to crystallized PET first. 2. Under 200PPM after about 4 hours dehumidifier processed. 3. Under 50 PPM after about more than 6 hours dehumidifier processed.

Lead time

 20mins More than 6 hours.

Material changeover

 1. Easy & faster. 2. There are only 1~1.5 times capacity of material hourly consumption in the buffer hopper. 1. Difficult & slowly. 2. There are 5~7 times capacity of material hourly consumption in the crystallizer & hopper.

Operation

   Simple--- By Siemens PLC control   It is difficult such as it must put a little crystallized PET in the crystallizer when beginning operation.

Maintenance

 1. Simple. 2. Lower maintenance cost. 1. Difficult. 2. Higher maintenance cost.

Previous:Plastic Lump Crusher

Next:PET Granulating line

Filament Dehydrator, PA Dryer, Small Dual Shaft Shredder, Bottle Shredder Machine, Heavy Duty Plastic Shredder, Ldpe Recycling Machine, Plastic Pellet Dryer, Pp Sack Bag Granulator, Plastic Densifier Machine, Bottle Disposal Machine,

Featured Products

Contact us

Please feel free to give your inquiry in the form below We will reply you in 24 hours